The best way to troubleshoot a century old Maytag washing machine

August 27, 2020 by Leslie Edison

 

In the past few days, some of our readers have come across Maytag Washing Machine Error Code for Centennial Troubleshooting. There are a number of factors that can cause this problem. Let's look at them now. Some common problems with a Maytag front loading washing machine are not stirring, spinning, draining or filling with water. The washing machine may vibrate during spinning or make noise during washing. Look, Maytag is a big brand, but if a washing machine doesn't work, it won't fit anyone.

 

 



There is nothing more frustrating than having a top loading Maytag washing machine fail to spin. Drying wet clothes takes forever, and no one has time for that.

It's good to know how to fix the problems yourself, because the solution can be simple.

3 Tips If Your Maytag Top Loading Washer Won't Spin


How do you reset the sensor on a Maytag washer?

Top Load Washer - Engine Hydraulic Shaft Reset
  1. Unplug the washing machine from the wall outlet for 1 minute.
  2. Reinsert the washer and lift and lower the cover six times within 12 seconds. You have 30 seconds to raise and lower the lid.
  3. The engine is now rebooted and ready to start the cycle.


The first step is to identify the source of the problem. This happens for many reasons, and knowing what to look for can help you figure out how to repair a washer that is not spinning.

Tip 1: Find The Stuck Clothes

Larger items or weights tend to settle on one side of the drum during the cycle. Try redistributing the load or removing some of the clothes and running the machine again to spin.

Tip 2: Check The Switch On The Cover


How do you run a diagnostic on a Maytag Centennial washer?

You are now ready to run the Maytag Centennial automatic diagnostic flush cycle. You will need to run Diagnostic Mode again, but this time turn the Centennial Wash Cycle knob clockwise until only the Spin light is on and press Start. The washing machine performs a short cycle in which all the functions of the washing machine are tested.


The switch prevents the washing machine from turning when the lid is open. This is usually a practical function. However, if this switch fails, the washing machine will not turn, even if the washing machine lid is closed Is dug.

Confirm that the lid switch is defective by first checking the plastic tab on the lid that activates the switch when closed. If the cover switch is damaged, it may not be able to activate.

If the tab is okay, the next step is to test the radio button yourself. When you close the wash cover, make sure it clicks into place. If you cannot hear it, the cover switch is probably defective and needs to be replaced.

Tip 3. Check Your Drive Belt


maytag washers centennial troubleshoot

If your Maytag Top Loading Washing Machine won't spin, check your drive belt to make sure it's not loose, damaged, or broken. If you also find that your washing machine is making a lot of noise when spinning, the drive belt may be the cause. Remove the rear panel from the Maytag washer and look for the drive belt to see if it is on the pulley system.



If you are loose, just tighten the pulley belt. However, if the belt is worn, damaged or broken, it should be replaced.

If you If troubleshooting efforts are difficult on a non-spin washing machine or repairs are too difficult, contact Sloan Appliance Support for instructions on how to repair your Maytag washing machine.



 

 

 

 

 

 

Related posts:

  1. How To Troubleshoot A Cd Drive

    Optical technologies There are two types of hard disk space for computers: magnetic and optical. With a magnetic drive, data is written magnetically onto spinning discs. Memory for optical storage media is similar to memory for magnetic storage media in basic operation, but reads and writes with light (optical) instead of magnetism. Although most magnetic disk storage devices can be read and written multiple times, many optical media are write-protected or write-once protected. Follow the convention in which we call magnets disks and optical disks. This is not a law or a rule, but most of the industry ...
  2. Nuvi Troubleshoot

    Here is a list of the most common problems with the Garmin Nuvi 200. Click on the link to view the repair manual. Over time, the battery loses its ability to hold a charge, which will shorten its life. After all, the battery cannot hold a charge at all. If Nuvi is still working after plugging in, the battery should be replaced. While this may seem obvious, first make sure the volume is turned on on your Nuvi. If this doesn't fix the problem, Nuvi may be frozen. Try restarting. If it is still ...
  3. Troubleshoot Error 500

    Internal Server Error 500 is a very generic HTTP status code that means an error has occurred on the website server. However, the server cannot grasp the exact problem. Are you a web manager? For more information, see Resolving 500 Internal Server Errors on Your Own Site at the bottom of the page if you see 500 Internal Server Errors on one or more of your pages. How you can see the 500 error The 500 Internal Server Error message can appear in several ways because each website is allowed to customize the message. Since the website you visit generates an internal ...
  4. Video System Troubleshoot Flowchart

    Flowchart: Troubleshooting Recording Issues for DW Spectrum Flowchart: Recording troubleshooting for DW Spectrum Save error DW Spectrum servers archive and store video from the camera on local hard drives while the cameras are streaming video ... Sometimes registration problems can arise due to: